wear resistant coatings > flotation cell wear corrosion resistant carborundum coating

flotation cell wear corrosion resistant carborundum coating

BD7052D flotation cell epoxy repair anti wear abrasion corrosion resistant coating
(flotation tank carborundum coatings)

Product description:
BD7052D flotation cell repair special anti corrosion wear resistant coating is the high performance wear resistant polymeric material
compounded by high performance abrasion resistant particle (silicon carbide,carborundum etc.) and modified toughening wear resistant
resin.Widely used in the repairing of the potion corrosion and abrasion caused by mineral grains in the flotation cell,can also used in the
preparation of wear & corrosion resistant pre-protective coating on the inner wall of flotation cell directly.

Performance features:
1.BD7052D flotation tank repair special anti abrasion corrosion resistant coating has excellent performance of wear resistant and corrosion resistant,room temperature curing,construction is convenient,as its performance is very outstanding,it is widely used in separation system
and matching several equipment production enterprise at present.

2.With excellent performance of abrasion resistant and corrosion resistant

3.With very high bonding strength to metal substrates.

4.The facade doesn’t flow,the construction is convenient,without very high technical requirements to the constructors.

5.Suitable for the repairing and protecting of various wear abrasion,corrosion working conditions.

Performance index:

Product name	Physical state	Operation time limit (25℃)	Curing time (25℃)	Range of application
BD7052D flotation cell special wear resistant coating	Paste	25 min	24 hours	used in the repairing of the potion corrosion and abrasion caused by mineral grains in the flotation cell,can also used in the preparation of wear & corrosion resistant pre-protective coating on the inner wall of flotation cell directly.

Color	Density (g/cm³)	Compressive strength (Mpa) GB1041-2008	Tensile strength (Mpa) GB6329-1999	Shear strength (Mpa) GB7124-2009	Bending strength (Mpa) GB1042-2008	Hardness after curing （Shore D） ASTM-D-2556	Working temperature (℃)
Drak gray	1.71	92	32	13	46	82	-60-90

How to use:
1.Surface treatment: Do the coarsening treatment for the pending-repair part,grinding with angle grinder or sand blasting etc,
the surface after coarsening treatment should be cleaned,the surface after this treatment should be the one coarsening,dry and
fresh substrates,should be no greasy dirt and dust.

2.Preparation:According to the weight ratio A:B=4:1, make A and B two components of BD7052D mix uniformly,and use it up within
30 min,every time the largest preparation quantity is not more than 25Kg.Generally it’s while construction and preparation,according to
the actual temperature,configuration can be properly a little more in winter,proper less in summer.If the temperature is too low,can
properly heat up the A component to reduce viscosity for easy to configure.

3.Coating:The suitable coating thickness of BD7052D flotaion cell repair anti wear corrosion resistant coating is 3~5mm.Make the well
mixed material be coating on the pending-repair part layer by layer,the first layer should be compacted,make it infiltrate fully with the
substrates.Repair the surface to be smooth after the coating is coated in the suitable size.

4.Curing:It can be put into using after curing 24 hours at the temperature of 25 degree,if the temperature is low,should heat it up or
prolong curing time to promote the curing.General construction in winter,can use iodine tungsten lamp to do irradiation heating with 40cm
distance from the coating.

Special version:
1.This parameter is for laboratory conditions,due to the actual working condition is more complex,suggest the users to do the pretest
according to actual working condition.

2.When the environment temperature is below 15℃,the curing time will prolong,should take proper heating measure.

3.When the environment temperature is more than 25℃ or the mixing quantity is too large,the curing speed will expedite,should properly
shorten the application time of coating after mixing.

Transportation storage:
Sealed storage in the cool and dry place.The warranty period is 12 months.Avoid placing it upside down, knocking against and transporting it
as a non-dangerous product during transportation.

Packing specification:
Two components,20Kg/group,packed in a plastic drum.Part A: 16Kg/drum, Part B: 4Kg/drum.

Product packaging picture of BD7052D flotation tank repair abrasion wear corrosion resistant epoxy coating:

------分隔线----------------------------